STEAMEMO 8 Port PoE+ Switch | Easy Smart Managed Ethernet Switch | Support VLAN, QoS | 120W Total PoE Budget | Fanless Metal | Plug & Play (Desktop/Wall Mount)

This 8-Port PoE Switch is designed to provide both data connectivity and power (Power over Ethernet) to compatible devices like IP cameras, Wi-Fi access points, and IP phones. Available in various configurations (e.g., 100Mbps or Gigabit ports, with additional uplink and SFP slots), it features a total power budget of 100W (or 120W), supporting 802.3af/at standards. This switch boasts features like VLAN support, PoE scheduling, and protection mechanisms, all housed in a fanless metal casing.Pros:– Provides power and Ethernet data over a single Ethernet cable (PoE/PoE+)– Supports a wide range of devices like IP cameras, Wi-Fi access points, and IP phones– VLAN support for improved security and traffic segmentation– Includes a PoE Scheduler to control power delivery based on time– Protection mechanisms against short circuits, over current, and over voltage– Metal casing and fanless design for durability, quiet operation, efficient heat dissipation– Easy to set up with plug-and-play functionality– Some models support an "Ultra-Far mode" for extending power and data transmission up to 250 metersCons:– Advanced management features (if available) might require some networking knowledge to fully utilize– Warranty isn't very long (1 year I believe)Overall this is a solid device, it works as expected and I've had no issues with it after 1 year. Plug and play POE, I use it to power Ring cameras around the house. Recommended for the price.

Great switch I use as the backbone for my entire house. Highly recommend

I had POE ports go dead in a matter of months and the company made it right with me. I have bought many from them and 99% work just fine. I do have 1 other that the main feed Ethernet ports the input port had a issue after a couple years but the Ethernet uplink once I switched it to that port the NVR ran ok again without the lag that the main port had a issue with. Overall it is a very good switch for the price

Intermittently turns off when touched even with a tight power connection but otherwise works well

The information regarding this switch is limited so I wanted to take a moment and tell my experience.I bought this 4 port switch as well as another 8 port switch for use with surveillance cameras and wifi access points. The installation uses around 600ft of OS2 single mode fiber optic cable. The reason I choose this switch is because it offered gigabit speeds across both POE ports and uplink ports as well as I can confirm the SFP port is full gigabit.The SFP ports have very good compatibility with every kind of SFP I tested.I can confirm it works with:Single mode 1310nm 1Gbe FS brand HP compatibleMulti mode 850nm 1Gbe Transition Networks and FinisarMulti mode 850nm 1Gbe CiscoSingle mode 1310nm 10Gbe FinisarMultimode 850nm 10Gbe FinisarCopper DAC direct-attach-cable 10Gbe 10GTek brandCopper RJ45 adapter 1Gbe HP compatibleNOTE: 10Gbe SFPs will only operate at 1Gb speeds.If you plan on using this with fiber optic cable, you need to ensure you are using the proper transceivers and patch cables for the installation. Single mode cables (identified as SMF SM or OS1 OS2) are usually yellow and support much longer lengths 2km+. SM typically uses 1310nm transceivers. Multi mode cables (identified as MMF MM or OM1,2,3,4,5) are different colors depending on speed and typically use 850nm transceivers. Orange OM1 is old for 100Mb or Gbe at shorter lengths. OM2 is also orange and rather old for 1Gbe, not backward compatible. OM3-4 are teal and support 10Gbe. OM5 is lime green not very common yet. One important note about fiber is that most uses duplex style connectors (2 fibers) and you must ensure you have outputs connected to inputs or else it will not work. Simplex transceivers are more expensive and use only a single fiber connector.I did not test the POE budget or the "VLAN" feature. The VLAN feature sounds more like port isolation. I might update the review later. I don't believe that this switch can support VLAN tagging.

I have the 5 port, 4 Port POE+ switch with SFP, and it has been in service with only two ports in use for the past 10 months, and went to plug in two more cameras via POE, and it fried both of the new cameras. I bought this because of POE and SFP, as it was the best price point, but now I don't view it that way. For some reason everything that was plugged in for the past 10 months via POE is still recognized and works properly, but the new devices i've tried plugging in either have gotten fried or just don't work on this switch, but before being fried worked fine on other switches.

I'm using this switch to power 16 IP cameras connected to an NVR. Setup was easy, Recognized and configured the cameras quicker than using the NVR. I downloaded and have been using the app. Configurations are minimal, you can turn the power on and off at each port and reboot the switch remotely. Sturdy box and fast data speeds.

installed and used it for Reolink PoE security cameras and works great!