amFilm Compatible with Samsung Galaxy S23 Ultra Screen Protector Tempered Glass and Camera Lens Protector 5G 6.8 inch, Fingerprint Sensor Compatible, UV Gel Adhesive Installation(2 Pack)

IMPORTANT: Inside the kit are two 'foil' wrapped wet cleaning clothes. Not the alcohol ones found in the little packet, but the packets with "Step 1" and "Step 2" labelled on them. DO NOT apply this wipe to your screen before applying the protector! I'm unsure what this wipe is, I'm guessing it's an oleophobic coating that goes on AFTER, but if you start wiping your display first with this wipe, you will end up with streaks all over the device. After I wiped my bare screen with it, I caught it just before I poured the adhesive. Make sure you are using the wipe containing alcohol, not the wipe with the two-step instructions.------Every time I buy a phone, I always buy 3-5 different types of screen protectors. This time, however, I only bought this one. I last used an Amfilm UV screen protector with my S21 Plus. There have been some changes that are very important to know before doing anything with this!The application was super straightforward. Take your device, apply the levelling foam pads, and open the cleaning materials and stickers packet. Use 2-3 of the smaller dust stickers to cover your ports! The S-Pen port (Or your pen can get glued in), the volume rocker, and the charge top microphone home. Use the isopropyl cleaning wipe (Please make sure it says it contains isopropyl alcohol) and wipe down the display. Use the microfiber to wipe off dust, apply the fixture, and use your larger dust stickers to remove dust. Apply glue, set the glass down and let it sit for about 2 minutes! Also, make sure the foam absorption pads are fully pressed in and make contact with the sides of the phone. After it's sat for a few moments, place the weight on top of the fingerprint sensor. Put the UV light over, and I let mine sit for about 2 minutes. I removed the weight and applied the uv back to the phone for another minute. And then I was done!TIP TO AVOID EXCESS ADHESIVE MESS: Push your phone out from the fixture by pressing the screen downwards and lifting it on the fixture. Apply the UV light again all around the device's top and sides. The UV glue that leaks around will begin to congeal into a thick piece you can peel off. This is easier to clean up the excess than wiping the phone for an hour. And now you're done!Pros:+Adhesive pushes micro particles of dust OUT+Finger print sensor works perfectly+Protective+Has not peeled on me+Very clear+Easy to install+Lots of adhesive!+Built in levelling meters.Cons:-It's easy to mix up the isopropyl alcohol with the other wet wipe (which I think is oleophobic and leaves streaks)-Little bit of a tedious and intimidating process for people not used to these kinds of protectors-No dedicated stickers to cover ports! The S20 and S21 both had black stickers to block off the ports.-I would prefer the protector cover the front camera, sadly there's a cutout-There are little 'offset' dots around the screen protector, which aren't super noticeable, but they can be-No fullscreen dust sticker like the regular glass protectors have. I would have loved to see full-screen dust stickers such as what the Amfilm iPhone 14 Pro max comes withMost of my cons are to do with things I wish the kit came with or was different. The screen protector is great, the kit is great, and it's the best for the money. I hope Amfilm considers these suggestions going forward!

I have used a lot of screen protectors over the last 25 years of my life of owning touch devices.I have used a lot of screen protectors from them over the last many years. Honestly they were my preferred screen protector until this.Unlike other iterations of this product they do not include any stickers to cover the ear speaker or tell you to do so in the directions. After the first attempt failed sue to air I tried again after watching the install video yet again. This time I did manage to get a air free install and was pretty happy with it until I answered my phone and could not hear anything but a muffled voice. The glue jammed up my speaker. I had to gently scrape it out with a small needle and a razor. I don't trust the water resistance in that speaker any more. The next day the corner of the screen protector started peeling up. At this point I had had such a terrible experience with the Note20 install that I did for my sons phone that I just pealed it off my phone. That brings up another issue. God help you if you remove the screen protector. Scraping the glue is a nightmare. Contacting their support was a joke and their satisfaction guarantee is a discouraged by volume of proof and blame the require.All in all I can not discourage this product enough.

Below is what is lacking, but - I will say that I WOULD buy this again despite all that. Its one of the best screen protectors.... Just several things lacking for installation (big things)---1. Did not come with a microfiber cloth - made installation very hard2. The tray (with installed levels) is not level. (Had to place stuff under it to level... As seen in pics)3. THERE IS NOT ENOUGH LIQUID ADHESIVE TO ADEQUATELY SPREAD ACROSS THE SCREEN. (Sort of - see below)4. Bubbles after installation. (See below)First attempt didn't even come close for the adhesive to reach the edge of the screen (maybe still a couple drops in tho). 2nd attempt I made sure to get every last drop out of the liquid adhesive cartridge - this was better BUT STILL NOT ENOUGH - sort of. The 2nd attempt, after like 2 minutes the adhesive managed to crawl to cover the entire screen - but the edges were SLOW to cover - and when it was going slow, it left micro bubbles (that I see after installation). Also that second attempt left 3 non-micro bubbles too...You can see all of this in the above pictures.Overall, the second attempt was OKAY - like it works. Hopefully it will last?? But this is lacking for a more expensive screen protector.

Love it! If you don't use your finger print sensor then it works great! It doesn't come with the annoying fingerprint cutout either. The installation process is a little tricky at first but if you mess up the first time then it's super easy to take the screen off. Try again with the second provided screen protector. The glue is also super easy to wipe off if you get it on the edges as well. Highly recommend and I've already bought a second kit. Again, the install can be a bit tricky but if you follow the directions exactly and even search for an installation step by step video on YouTube then it will be so much easier and work how it should.

First , I got a chip on the protector and as promised they sent out a replacement. The original kit included 3 protectors. I messed up the first two.The third protector worked great. I have been using it for over a year now. I do have multiple cracks and chips but the phone is protected. No bubbles or lifting corners.The trick is to realy clean the screen all the way to the sides.Once I dropped a ceramic tile on the screen and. Whike the screen protector blew out a big chunk my screen was protected.When I bought the protector I put in for a warranty replacement. As promised they sent me a new kit.I put in for another warranty but was told I had used all my warranty up. So much for life time warranty.This is a nice product.